pair_style zbl command
Accelerator Variants: zbl/gpu, zbl/kk, zbl/omp
pair_style zbl inner outer
inner = distance where switching function begins
outer = global cutoff for ZBL interaction
pair_style zbl 3.0 4.0 pair_coeff * * 73.0 73.0 pair_coeff 1 1 14.0 14.0
Style zbl computes the Ziegler-Biersack-Littmark (ZBL) screened nuclear repulsion for describing high-energy collisions between atoms. (Ziegler). It includes an additional switching function that ramps the energy, force, and curvature smoothly to zero between an inner and outer cutoff. The potential energy due to a pair of atoms at a distance r_ij is given by:
where e is the electron charge, \(\epsilon_0\) is the electrical permittivity of vacuum, and \(Z_i\) and \(Z_j\) are the nuclear charges of the two atoms. The switching function \(S(r)\) is identical to that used by pair_style lj/gromacs. Here, the inner and outer cutoff are the same for all pairs of atom types.
The following coefficients must be defined for each pair of atom types via the pair_coeff command as in the examples above, or in the LAMMPS data file.
\(Z_i\) (atomic number for first atom type, e.g. 13.0 for aluminum)
\(Z_j\) (ditto for second atom type)
The values of \(Z_i\) and \(Z_j\) are normally equal to the atomic numbers of the two atom types. Thus, the user may optionally specify only the coefficients for each \(i==i\) pair, and rely on the obvious mixing rule for cross interactions (see below). Note that when \(i==i\) it is required that \(Z_i == Z_j\). When used with hybrid/overlay and pairs are assigned to more than one sub-style, the mixing rule is not used and each pair of types interacting with the ZBL sub-style must be included in a pair_coeff command.
The numerical values of the exponential decay constants in the screening function depend on the unit of distance. In the above equation they are given for units of angstroms. LAMMPS will automatically convert these values to the distance unit of the specified LAMMPS units setting. The values of Z should always be given as multiples of a proton’s charge, e.g. 29.0 for copper.
Styles with a gpu, intel, kk, omp, or opt suffix are functionally the same as the corresponding style without the suffix. They have been optimized to run faster, depending on your available hardware, as discussed on the Speed packages doc page. The accelerated styles take the same arguments and should produce the same results, except for round-off and precision issues.
These accelerated styles are part of the GPU, USER-INTEL, KOKKOS, USER-OMP and OPT packages, respectively. They are only enabled if LAMMPS was built with those packages. See the Build package doc page for more info.
You can specify the accelerated styles explicitly in your input script by including their suffix, or you can use the -suffix command-line switch when you invoke LAMMPS, or you can use the suffix command in your input script.
See the Speed packages doc page for more instructions on how to use the accelerated styles effectively.
Mixing, shift, table, tail correction, restart, rRESPA info
For atom type pairs i,j and \(i \neq i\), the \(Z_i\) and \(Z_j\) coefficients can be mixed by taking \(Z_i\) and \(Z_j\) from the values specified for \(i == i\) and \(j == j\) cases. When used with hybrid/overlay and pairs are assigned to more than one sub-style, the mixing rule is not used and each pair of types interacting with the ZBL sub-style must be included in a pair_coeff command. The pair_modify mix option has no effect on the mixing behavior
The ZBL pair style does not support the pair_modify shift option, since the ZBL interaction is already smoothed to 0.0 at the cutoff.
The pair_modify table option is not relevant for this pair style.
This pair style does not support the pair_modify tail option for adding long-range tail corrections to energy and pressure, since there are no corrections for a potential that goes to 0.0 at the cutoff.
This pair style does not write information to binary restart files, so pair_style and pair_coeff commands must be specified in an input script that reads a restart file.
This pair style can only be used via the pair keyword of the run_style respa command. It does not support the inner, middle, outer keywords.
(Ziegler) J.F. Ziegler, J. P. Biersack and U. Littmark, “The Stopping and Range of Ions in Matter,” Volume 1, Pergamon, 1985.